選擇封裝方式(默認的封裝方式是HDLC,您可根據與您的路由器相連選用的封裝類型來決定用什么樣的封裝類型

　　No serial cable seen.

　　Choose mode from (dce/dte) [dte]:

　　(因為沒有連串口線所以會讓您選擇設備類型)

　　Configure IP on this interface? [yes]: y

　　(在接口上配置IP)

　　Configure IP unnumbered on this interface? [no]:

　　IP address for this interface: 172.16.0.5

　　配置該接口的IP地址(在此地址為172.16.0.5)

　　Subnet mask for this interface [255.255.0.0] : 255.255.255.252

　　配置該接口的子網掩碼.(默認的是255.255.0.0,可以手工輸入修改為255.255.255.252)

　　Class B network is 172.16.0.0, 30 subnet bits; mask is /30

　　(以下配置同上)

　　Do you want to configure FastEthernet0/1 interface? [yes]:

　　Use the 100 Base-TX (RJ-45) connector? [yes]:

　　Operate in full-duplex mode? [no]: y

　　Configure IP on this interface? [yes]: y

　　IP address for this interface: 172.16.0.9

　　Subnet mask for this interface [255.255.0.0] : 255.255.255.252 Class B network is 172.16.0.0, 30 subnet bits; mask is /30

　　The following configuration command script was created:

　　(把您的配置顯示出來)

　　hostname aaa

　　enable secret 5 $ul/V$ezbZFgvzGHD.YPSieC0Ew/

　　enable password RouterA

　　line vty 0 4

　　password ccc

　　no snmp-server

　　!

　　ip routing

　　no bridge 1

　　!

　　interface FastEthernet0/0

　　media-type 100BaseX

　　full-duplex

　　ip address 192.168.0.1 255.255.255.0

　　!

　　interface Serial0/0

　　encapsulation hdlc

　　ip address 172.16.0.5 255.255.255.252

　　!

　　interface FastEthernet0/1

　　media-type 100BaseX

　　full-duplex

　　ip address 172.16.0.9 255.255.255.252

　　dialer-list 1 protocol ip permit

　　dialer-list 1 protocol ipx permit

　　!

　　end

　　以下提示您是否保存這次設置

　　[0] Go to the IOS command prompt without saving this config.

　　[1] Return back to the setup without saving this config.

　　[2] Save this configuration to nvram and exit.

　　Enter your selection [2]: 2

　　選擇2保存設置并存入NVRAM中

　　Building configuration...

　　[OK] Use the enabled mode 'configure' command to modify this configuration.

　　Press RETURN to get started!

　　路由器重新啟動

　　00:00:08: %LINK-3-UPDOWN: Interface Serial0/0, changed state to down

　　00:00:08: %LINK-3-UPDOWN: Interface FastEthernet0/0, changed state to up

　　00:00:08: %LINK-3-UPDOWN: Interface FastEthernet0/1, changed state to up

　　00:00:09: %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0/0, changed state to down

　　00:00:09: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to down

　　00:00:09: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/1, changed state to down

　　00:03:18: %IP-5-WEBINST_KILL: Terminating DNS process

　　00:03:24: %SYS-5-RESTART: System restarted --

　　Cisco Internetwork Operating System Software

　　IOS (tm) 3600 Software (C3640-I-M), Version 12.1(2)T, RELEASE SOFTWARE (fc1)

　　Copyright (c) 1986-2000 by cisco Systems, Inc.

　　Compiled Tue 16-May-00 12:26 by ccai

　　RouterA>

　　進入用戶模式

　　RouterA>en

　　Password:

　　RouterA#

　　進入全局模式

　　RouterA#sh run

　　查看現在運行的配置

　　Building configuration...

　　Current configuration:

　　!

　　version 12.1

　　service timestamps debug uptime

　　service timestamps log uptime

　　no service password-encryption

　　!

　　hostname RouterA

　　!

　　enable secret 5 $ul/V$ezbZFgvzGHD.YPSieC0Ew/

　　enable password bbb

　　!

　　memory-size iomem 25

　　ip subnet-zero

　　!

　　interface FastEthernet0/0

　　ip address 192.168.0.1 255.255.255.0

　　speed auto

　　full-duplex

　　!

　　interface Serial0/0

　　ip address 172.16.0.5 255.255.255.252

　　clockrate 2000000

　　!

　　interface FastEthernet0/1

　　ip address 172.16.0.9 255.255.255.252

　　speed auto

　　full-duplex

　　!

　　ip classless

　　no ip http server

　　!

　　dialer-list 1 protocol ip permit

　　dialer-list 1 protocol ipx permit

　　!

　　line con 0

　　transport input none

　　line aux 0

　　line vty 0 4

　　password ccc

　　login

　　!

　　end

　　現在您就完成了了一個新路由器的基本配置,接下來就可以進行進一步的詳細配置了